<!-- @page { margin: 2cm } P { margin-bottom: 0cm } P.western { font-size: 11pt } P.cjk { font-size: 11pt } H1 { margin-top: 0cm; margin-bottom: 0cm } H1.western { font-family: "Times New Roman", serif; font-size: 12pt } H1.cjk { font-family: "Lucida Sans Unicode"; font-size: 12pt } H1.ctl { font-family: "Tahoma"; font-size: 12pt } H2 { margin-top: 0cm; margin-bottom: 0cm; text-align: center; text-decoration: underline } H2.western { font-family: "Times New Roman", serif; font-size: 12pt } H2.cjk { font-family: "Lucida Sans Unicode"; font-size: 12pt } H2.ctl { font-family: "Tahoma"; font-size: 12pt } -->

SERIES 5 MULTI.

Bingo Operating Instructions.

Connect the power supply.

Series 5 Multi enters a test routine and resets to Bingo mode 1 – 90, (GL 90).

(If you do not wish to play bingo please see below).

Use the SELECT switch to change the game required.

Press SELECT to change from 1-90, 1-80,1-75,1-12 and back to 1 – 90.

When the game length you wish to play is displayed press CLEAR.

The display now reads JP 0. ( Jackpot is not available on 1 – 12, (GL 12).

The zero indicates that a jackpot number is not required.

To enter a jackpot number press the SELECT switch to increase the jackpot number, and use the RECALL switch to decrease the jackpot number required.

The number increases or decreases by one for each press of the switch.

Numbers below 35 are not permitted.

0 increments to 35 with one press of the switch, and similarly 35 reverts to 0 with one press.

Once the jackpot number you require is displayed press CLEAR.

Series 5 Multi is now set to play bingo.

To select numbers to call press SELECT.

The number selected is displayed to the operator only.

Release the SELECT switch to display the number to the audience.

Press SELECT again for the next number.

The last number selected is now shown in the Last Number display.

The number selected prior to the last number is shown blinking on the matrix.

Repeat until the game is won.

To recall numbers in the reverse order to which they were called press RECALL.

Recall mode is indicated by the blinking decimal points.

Once all selected numbers have been recalled, Series 5 Multi returns to select mode.

To return to select mode without recalling all selected numbers, press SELECT.

Press SELECT to select more numbers.

If a jackpot number has been set, the displays flash when this number of calls is reached.

To cancel a game press CLEAR twice.

Power Supply: 9 volts d.c. Regulated 350mA. Polarity: Centre Negative.

Use only the power supply supplied with Series 5 Multi.

DO NOT use an unregulated power supply. This may cause damage to Series 5 Multi.

DO NOT use a power supply greater than 9 volts d.c. This will cause damage to Series 5.

Selection of Raffle Numbers.

Use the MODE switch to display raffle. Press SELECT

The display shows Lo

Key in the Lo (start) number. Press SELECT.

The display shows Hi

Key in the Hi (finish) number. Press SELECT.

Press CHECK to verify the Lo (start) number, and again to verify the Hi (finish) number.

Press CHECK again to display dashes.

Press SELECT to select a winning number, and repeat as required.

NOTE: The Lo number must be Lower than the Hi number or ERROR will be displayed..

Press RECALL to display the winning numbers in the order they were selected.

Recall mode is indicated by the blinking decimal points.

Once all selected numbers have been recalled, Series 5 Multi returns to select mode.

To return to select mode without recalling all selected numbers press SELECT.

Press SELECT for more random numbers.

Press CLEAR twice to erase all selected numbers.

NOTE: Clear all selected numbers before switching between raffle and tote modes.

Selection of Tote Numbers.

Press MODE to display tote d for tote selections allowing duplicate numbers (e.g. 12 – 12),

or tote nd for selections allowing no duplicate numbers.

Press SELECT.

Key in the lo (start) number in the range 0 – 99. Press SELECT.

Key in the hi (finish) number in the range 0 –99. Press SELECT.

Press CHECK to verify the lo (start) number and again to verify the hi (finish) number.

Press CHECK again to display dashes.

Press SELECT to select the first tote number and again for the second.

Repeat for further selections

NOTE:The Lo number must be Lower than the Hi number or Error will be displayed.

Press RECALL to display winning tote selections in their original order.

Recall mode is indicated by the blinking decimal points.

Once all selected numbers have been recalled, Series 5 Multi returns to select mode.

To return to select mode without recalling all selected numbers press SELECT.

Press SELECT for more winning selections.

Press CLEAR twice to erase all selected numbers.

Setting Speed of Number Selection.

Use the MODE switch to select raffle.

Whilst raffle is displayed, press any of the switches marked 1 – 6 to determine the speed at which selected winning numbers are displayed.

Press 1, for the quickest selection speed; 2,3, 4 or 5, for the slowest selection speed.

Press 6 to display selected numbers instantly.

Sp Set will be displayed briefly, followed by raffle.

Press SELECT and enter the lo and hi numbers.

The selected speed will apply to raffle and tote selections and will be stored for future use.